Fabricating the aluminum intercooler end tank

Cool Your Charge! The 15’ WRX Front-Mount Intercooler Build, Part 2: Core and Support Fabrication

Interested in picking up our 2015 WRX FMIC kit? Check out more details on our product page linked below!

Mishimoto Subaru WRX Front-Mount Intercooler Kit

Crash Beam Fabrication

After an unsuccessful test fit of our existing bumper beam on the 15’, we started from scratch to create a beam specific for the 15’ chassis. First we hacked off the end tanks of our cooler so we were left with a bare core. This would provide some freedom to design our crash beam and later work on the end tank direction. Next we cut out some new mounting plates and fit them into position.

Intercooler crash beam mounting plates
Intercooler crash beam mounting plates
Intercooler crash beam mounting plates
Intercooler crash beam mounting plates

Next we fabricated a beam for mounting the cooler. The beam would run parallel across the front of the vehicle and attach to each mounting plate.

Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication

We then added the connector legs to attach this beam to the mounting plates. After a few tweaks, this guy was in position and ready to rock!

Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication
Intercooler crash beam fabrication

Intercooler End Tank Fabrication

Now that our crash beam was in place, we turned our attention to the end tank design for this kit. As noted earlier, the existing end tanks for this cooler were far too long; we would need shorter tanks to allow space for pipe routing on the 15’.

We started by modeling these tanks in a foam material. This material is easier to modify compared to aluminum, and we can mold it to our preferred shape and size.

Foam intercooler end tank prototype
Foam intercooler end tank prototype
Foam intercooler end tank prototype
Foam intercooler end tank prototype

Next, we pulled out the TIG and got to work replicating these tanks in aluminum, as we needed to test this kit once complete.

First, the component was printed in a flat-pack drawing, which indicates the cutout and bends needed to create this tank from a flat sheet of aluminum.

Fabricating the aluminum intercooler end tank
Fabricating the aluminum intercooler end tank

This piece was then cut out and bent to position!

Fabricating the aluminum intercooler end tank
Fabricating the aluminum intercooler end tank

We then handed the torch to Dan (literally) and set him to work welding the end tank. A pipe end was also welded to complete the construction. Here is the finished tank next to our original foam prototype.

Aluminum intercooler end tank prototype (left) and foam prototype (right
Aluminum intercooler end tank prototype (left) and foam prototype (right

And finally we fully welded this tank to our core.

Prototype intercooler
Prototype intercooler

Keep in mind this is strictly a prototype for functionality and test fitting. Our final intercooler design will feature the same core combined with cast end tanks in this same shape. Cast tanks provide a more robust construction with far less failure points compared to a sheet metal end tank. Additionally, by casting this component we can create an extremely smooth internal surface that will provide the best possible airflow through the core.

This core is already proven, so as long as our dyno testing gives us positive results, we will be sticking with this very efficient bar-and-plate core. Take a closer look!

Mishimoto intercooler core
Mishimoto intercooler core

That’s all we have for this round of development. Check back with us next time for a look at our plans for pipe routing on the mighty 15’ WRX.

Thanks!

Interested in picking up our 2015 WRX FMIC kit? Check out more details on our product page linked below!

Mishimoto Subaru WRX Front-Mount Intercooler Kit

 

Leave a Reply

Your email address will not be published. Required fields are marked *